跳至主要内容

What Methods should be Paid Attention to During the Construction of Geomembrane

 

What Methods should be Paid Attention to During the Construction of Geomembrane


Construction method:

 

Do not drag or pull the geomembrane during transportation to avoid injury from sharp objects.

1. Extend from the bottom to the high position, don't pull it too tightly, and leave a margin of 1.50% to prepare for local sinking and stretching. Taking into account the actual situation of this project, the slope shall be laid from top to bottom;

2. The longitudinal joints of two adjacent panels should not be on the same horizontal line, and should be staggered by more than 1m;

3. Longitudinal joints should be more than 1.50m away from the dam foot and bend foot, and should be located on a plane;

4. Slope first and bottom of the field;

5. When laying on a slope, the film spreading direction should be basically parallel to the line of maximum slope.

Layout:

1. Before laying the geomembrane, the corresponding qualified acceptance certificate of the civil engineering should be obtained.

2. Before cutting the geomembrane, the relevant dimensions should be accurately measured and then cut according to the actual size. Generally, it is not advisable to cut according to the size shown in the figure. It should be numbered piece by piece and recorded in detail on the special form.

3. When laying geomembrane, we should try to minimize the number of welds, and save raw materials as much as possible under the premise of ensuring quality. At the same time

Easy to ensure quality.

4. The lap width of the seam between the film and the film is generally not less than 10cm, usually the welding seam arrangement direction is parallel to the maximum slope, that is, arranged along the slope direction.

5. Usually in corners and deformed areas, the length of the joints should be as short as possible. Except for special requirements, on slopes with a slope greater than 1:6, within 1.5 meters from the top slope or stress concentration area, there should be no welds as far as possible.

6. When laying the geomembrane, avoid artificial wrinkles. When the temperature is low, it should be tightened and flattened as much as possible.

7. After the geomembrane is laid, it is necessary to minimize walking and moving tools on the surface of the membrane. Anything that can cause harm to the impermeable membrane should not be placed on the membrane or carried on the membrane to avoid damage to the membrane. Cause accidental damage.


What Methods should be Paid Attention to During the Construction of Geomembrane

评论

此博客中的热门博文

What Is a Dimpled Drainage Matting?

What Is a Dimpled Drainage Matting? Most  dimpled drainage matting  consist of a polypropylene or high-density polyethylene  sheet, molded into a series of raised knobs, or dimples. Polyethylene dimpled drainage mat helps water flow away from the foundation. Without it, water can stay trapped against the concrete or pool at the bottom. Drainage mats come with a dimpled design that lets water accumulate and flow away, creating an air gap. When a dimple mat is placed against a concrete wall, the dimples make the plastic stand out from the wall, leaving a free-draining air space between the plastic and the concrete. If any water reaches this air space, it easily flows to the bottom of the dimple mat. As water flows, it picks up small particles of silt and soil. When water stops moving—like when it reaches a concrete wall—silt and soil will accumulate, further increasing the pressure against the foundation. A drainage ma's membrane protects the mat from sediment clogging...

Welcome to Shandong Luyuan

Shandong Luyuan Engineering Material Co. Limited   is a professional and comprehensive enterprise which is specialized in researching, developing and manufacturing geosynthetic products , who are one of the Geomembrane manufacturers in China . Luyuan owns a number of advanced-technology geosynthetics production lines,including automatic geocell welding production,geogrid welding production line, geomembrane blowing production line, non woven geotextile production line, plastic mould injection machine.   Luyuan   integrates cutting-edge technologies in geosynthetics, accounts on strong technologies, persists in strict quality testing standards and provides high-quality products and services. The reasonable prices, superior products, perfect services and customers'satisfaction are Luyuan's eternal pursuits. Luyuan products are widely used in water conservancy, railway, highway projects including power plants, waterways, ports, airports, tunnels, landfills, reservoirs, dams ...

Geocell For Slope Protection

  Geocell For Slope Protection Everyone knows that when a car is driving on the desert, it will press two deep tracks, the pressed part sinks deeply, and the two sides of the track will bulge high. If the vehicle behind continues to advance along the rut, the sinking part will sink further, and the bulging part will bulge further, until the bulging part hits the chassis of the car, and the sinking rut buries most of the wheels, making it impossible to move forward. The reason for this is because when an external load acts on the surface of the foundation, according to Planttel theory and Taylor theory, it can be known that under the action of concentrated load, the active zone is compressed and sinks, and the force is decomposed and transmitted to the transition on both sides. Zone, the transition zone is passed to the passive zone, and the passive zone will deform and bulge without restriction. Features: 1. It is flexible in expansion and contraction, and can be folded during tran...